Lithium Ion Battery Power 12V 100Ah With Bluetooth For Energy
Storage / Base Station
Description of LiFePO4 Battery
1. More than 3000 cycles time and 2 years long guarantee time.
2. Very suitable for RV and replace the traditional lead acid battery
with battery size: 278mm x 175mm x 190mm.
3. More rechargeable time, longer life time, economic and
environmental protection.
4. Prismatic cells UL1642 & UN38.3 & ICE62619 certified, packs CE &
38.3 & MSDS.
5. APP control monitoring.
6. OEM & ODM service are availble.
PERFORMANCE / EFFICIENCY
A Bely LiFePo4 battery can do more than 96% of the energy made
available directly to save. A 100% utilization of the existing
capacity takes place with the same output voltage.
Battery Charging
Use the suitable lithium battery charger. Waiting until the battery
is fully charged.
LiFePO4 technology offers high-powered cell performance compatible
with lots of lithium-ion application to deliver more power and
extend long life. Also built with bluetooth function allow you to
read battery status freely anytime.
Specification of Lifepo4 Battery 12v 100AH
| Specification | Parameter | Remarks |
| Nominal | Voltage | 12.8V |
| Capacity | 100Ah/1280Wh |
| Physical | Dimension | 278mm x 175mm x 190mm |
| Weight | 12KGS |
| Electrical | Working Voltage Range | 10~14.6V |
| End of Charge Voltage | 14.4~14.6V |
| Recommended Charging Current | 50A |
| Max. Charging Current | 80A |
| Max. Continuous Discharging Current | 100A |
| Peak Discharging Current (≤20 sec.) | 150A |
| Others | Charging Temperature Range | 0~55℃ |
| Discharging Temperature Range | -20~60℃ |
| Storage Temperature Range | -20~60℃ |
| Cycle Life | ≥3000Cycles |
| Internal Impedance | ≤20mΩ |
| Battery Cells Type | Prismatic |
| Connector | Copper pillar |
| Material | ABS(anti-UV) |
| Charging mode | CCCV/IU |
| Protection Class | IP65 |
Battery Management System(BMS)
Passive balancing (active balance optional ), low voltage cutoff,
high voltage cutoff, short circuit protection and temperature
protection for increased performance and longer life. Besides,
Bluetooth function for option that enables to monitor battery
status, such as, voltage, capacity and so on.
Battery Benefits
Light weight
High discharge rate
Good consistency, low self discharge
High performance traction/storage battery
Integrated (BMS) battery management system
One to one replaceable with lead acid battery
With short-circuit production function, safe and reliable
APPLICATION AREAS
UPS, Solar, Wind, Mobile generator, Back up power
Scooter, E-bike, Golf cart, E-motor, E-tour car, tricycle
Electric drill, electric saw, lawn mower and so on
Remote control cars, boat, aircraft, toys
Medical devices, equipment and portable equipment
Bluetooth, GPS, Wearable device, Power supply, Wireless
Install the LiFePO4 battery
Lithium LiFePo4 batteries are heavy. Make sure it is adequate and
safe attach and always use the appropriate transport equipment.
In an accident unsecured, batteries could become a projectile!
Always take carefully with lithium batteries.
Make absolutely sure that the LiFePO4 battery is not connected with
reversed polarity.
Should the battery be connected incorrectly, the BMS electronics
will be irreparably damaged and must be replaced with a new BMS
board. This is not a warranty case.
Important instructions
Do not open the LiFePO4 battery without consulting the dealer.
Unauthorized opening of the battery voids the manufacturer's
warranty.
▪ Only use the battery for the application for which it is
intended.
▪ Do not short-circuit the LiFePO4 battery. The cable connections
to the consumers must go through a backup to be protected.
▪ Installation and maintenance may only be carried out by qualified
specialists.
▪ Do not expose to permanent direct sunlight. Protect from the
effects of heat. Temperatures above +60 ° C can damage the battery.
▪ Use only compatible chargers. The battery is in a longer storage
of all disconnect devices.
▪ Pay attention to proper assembly.
▪ Avoid damage of any kind, for example by falling, drilling, etc.
(Risk of short circuit).
▪ Always keep the battery dry and clean.
▪ Note the plus (+) and minus (-) markings on the LiFePO4 battery
and the device and pay attention to the correct polarity.
▪ The cycle capacity may vary due to the change in the working
temperature and the charge and discharge rate differ from the
nominal capacity.
▪ Suitable for parallel connection maximum four batteries (If need
series connection, the BMS should be customized with higher cost).
Before connecting, bring to the same charge level. Batteries from
different manufacturers or different types should not be
interconnected.
Warning & Tips
1. Do not throw battery into water or make it wet;
2. Keep the battery away from heat source(like fire or heater);
3. Do not throw the battery into fire or heat the battery;
4. Forbid to hammer to trample the battery;
5. Forbid disassembling the battery in anyway
FAQ:
Q1. Can I have a sample order?
A. Yes, we welcome sample order to test and check quality.
Q2. Do you have any MOQ limit?
A.Yes, we have MOQ for mass production, it depends on the different
part numbers. 1~10pcs sample order is available. Low MOQ, 1pc for
sample checking is available.
Q3. How to proceed with an order?
A. Firstly let us konw your requirements or application. Secondly,
we quote according to your requirements or our suggestions. Thirdly
customer confirms the samples and places a deposit for formal
order. Fourthly we arrange the production.
Q4. Is it OK print my logo on the product?
A. Yes. Please inform us formally before our production and confirm
the design firstly based on our sample.
Q5. Which certificates do you have?
A. We have CE/FCC/ROHS/UN38.3/MSDS ... etc.
Q6. How about warranty?
A. 2 years warranty.
